Brand Name:icchipcn.com
Condition:New
Type:Logic ICs
Supply Voltage:3-5v
Dissipation Power:1w
is_customized:Yes
Operating Temperature:0-85
Application:Computer
Package:TQFP

For ST-Link V2 Mini STM8 Simulator Download

1. Support the full range of STM32 SWD interface debugging, simple interface (including power supply), 4 line speed, stable work; Interface definition shell directly address! Don't need to read instructions!

2, support all series STM8 SWIM download debugging (common development environment such as IAR, STVD etc.) are supported. Support the software version is as follows:

For ST - LINK Utility 2.0 and above

STVD 2 and above

STVP 3.2.3 and above

IAR EWARM V6.20 and above

IAR EWSTM8 V1.30 and above

KEIL RVMDK V4.21 and above

3. Support the firmware upgrade automatically, to ensure that the ST company product support. When they leave the firmware has been upgraded to the latest V2. The J17. S4.

4. Increase the 5 v power output, the output it can protect the I/O port, not afraid of error cause damage of For ST - LINK V2!

5. Easy interface to use pure copper plating 2.54 spacing horn, with 20 cm dupont line, can deal with different target board line sequence, flexible connection;

6. Use U disk aluminum alloy shell to protect the mainboard, convenient to carry, not afraid of static electricity, not afraid of tumbling.

STM32F103C8T6 ARM STM32 Minimum System Development Board Module For Arduino

This is a core chip based on for CS32F103C8T6 ARM core board, features are as follows:

1, the board based on the most basic MCU circuit, 8M and 32768 crystal circuit, USB power supply circuit.

2, the core board is divided into two rows leads to all the I / O port.

3, with SWD simulation debug download interface, simple and convenient, debugging speed.

4, the use of the Mirco USB interface, you can do USB communication and power supply, USB interface, compatible with the ordinary Andrews mobile phone charger interface.

6, RTC crystal Epson brand, easy to start, more stable.

7, with double pin, but the pin does not default welding, the user according to their own application scenarios to choose their own welding direction. If welding is required, please tell the owner.

Keil can be used to compile, IAR compiler, can be downloaded through the J-Link or USART1 procedures, the procedures are the owner and debugging procedures, there are problems can consult the owner.

Chip Description:

1, 32F103C8T6

Package Type: LQFP;

Number of pins: 48;

Kernel: Cortex-M3;

Operating frequency: 72MHz;

Storage resources: 32K Byte Flash, 20KByte SRAM;

Interface Resources: 2x SPI, 3x USART, 2x I2C, 1x CAN, 37x I / O ports,

Analog-to-digital conversion: 2x ADC (12-bit / 16-channel)

Timers: 3 general timers and 1 advanced timer

Debug Download: Support JTAG / SWD debug interface to download, support for IAP.

2, RT9193: 3.3V regulator chip, the maximum output of 300mA.

Interface description:

1, SWD interface: support for simulation, download and debug.

2, Mirco USB interface: power supply and USB communication, does not support the download.

3, USART1 interface: USART1 can be used to download the program, or use the USART1 for communication.

4, MCU pin interface: leads all I / O port pins, easy to connect with peripherals.

5, 5V and 3.3V power input and output interface: commonly used in external power supply, or with other modules for common ground treatment

Other Device Description:

1, Power LED (PWR): Power indicator status, can determine whether the power supply is stable.

2, the user LED (PC13): to facilitate the I / O output test or indicate the program running.

3, start jumping choose programming mode: (1, the user flash memory 2, SRAM 3, system memory).

4, reset button: reset chip for the user program.

5, 8M Crystal: The frequency can be set to make the system clocked at 72MHz.

6,32.768KHz Crystal: Available for built-in RTC, or for calibration.

STM32F103C8T6 is out of stock and on the verge of discontinuation, the core board is replaced with STM32F103C6T6.

In most cases, C6T6 can replace C8T6. If the program is relatively large or the serial port 3 used cannot be replaced, what about the program size Please see the introduction below.

The difference between STM32F103C6T6 and C8T6:
1. C6T6 has no serial port 3;
2. The flash of C6T6 is 32K, and the flash of C8T6 is 32K;
3. The RAM of C6T6 is 10K, and the RAM of C8T6 is 20K.
After keil software is compiled, it will prompt the usage of Code, RO-data, RW-data, ZI-data; where falsh="Code"+"RO-data"+"RW-data", RAM="RW-data"+ "ZI-data".

Hardware resources:
1. One STM32F103C6T6 main chip
2. SMD 8M crystal oscillator (up to 72M through the internal PLL of the chip) ST official standard parameters
3. 3.3V voltage regulator chip, maximum 800mA current
4. One miniUSB interface, which can supply power to the system version and reserve USB communication function
5. Reset button
6. One standard SWD port, support JLink, STLink, JLINK OB
7. BOOT select port
8. IO extension header 20pin x 2
9. 1 power indicator
10. One function indicator, used to verify the basic functions of the IO port
11. Reserve a serial port for easy connection with the 5V development board, and you can use the serial port to program
12. High-performance Epson 32768Hz crystal oscillator, the price is 10 times the price of in-line crystal oscillator, easy to start vibration
13. 10K RAM, 32K ROM, TQFP48 package