Condition:New
Type:Logic ICs
Supply Voltage:DC12V
Model Number:Metal case
The following conditions must be met:
1: Metal container wall thickness requirements 3-8MM
2: Requires no paint on the container
3: Requires no more liquid impurities
4: The diameter of the container should not exceed two meters
5: The temperature is up to 60 degrees
6: Requires that the inside of the container can only have liquid
I. Overview:
The XKC-C352 high and low level controller can be used with the XCK-Y25 non-contact liquid level sensor. It can also be used with other liquid level sensors such as float balls to achieve low liquid level alarms generated by the liquid level sensor when the liquid level of the container is too low. When the signal is sent, the pump automatically starts to add the liquid level. When the liquid level reaches a certain height, the high liquid level sensor sends a signal to automatically stop the pump operation, thereby realizing the automatic control of the liquid level of the container. The controller self-checking protection ability with pump air pump stop detection, high level overflow detection, pumping timeout detection; control diversification can be manual mode control water pump, automatic mode control water pump; multiple output modes, one load output control power is high Up to 1600W, one-way alarm output control up to 800W, relay normally open output, can also exchange 110V or 220V output. The controller is fully functional and suitable for a wide range of applications.
Second, the characteristics:
1, compatibility is strong, can use a variety of liquid level sensor input control;
2, strong protection, with waterproof pump idling protection and water level overflow detection output, comes with 4 hours overtime pumping alarm;
3, relay dry node output, can be applied to a variety of load control;
4, control diversification, the pump can be controlled manually or automatically;
5, the installation is simple and convenient, can be screwed and installed can also be installed on the electric box track;
Third, electrical parameters:
Model
|
XKC-C352V2
|
Explain
|
C352 high and low level automatic controller
|
Input voltage
|
AC100V-220V，50/60Hz
|
Working voltage
|
DC12V
|
Working current
|
工作电流≤110 mA，静态耗电流≤20mA
|
Load power
|
Below 1.6KW (overload or for three-phase pumps requires an AC contactor)
|
Alarm output
|
800W (resistive load) normally open normally closed output
|
Output mode
|
Relay normally open normally closed or AC AC110V/220V two 2 select one output
|
Input signal
|
Low level sensing signal input;
High level sensing signal input;
Pump idling detection signal input;
Water overflow alarm signal input;
|
Sensor interface voltage
|
DC12V
|
Working temperature
|
-10~75℃
|
Outline size
|
115*90*40
|
Signal input and relay output corresponding map:
Input signal
|
Load output
|
|
Alarm signal status
|
Alarm Output
|
Low is 0, high is 0
|
Normally open, normally closed
|
![]()
Circulation
|
Low is 0, high is 1
|
Normally open, normally closed
|
Low is 1, high is 0
|
Normally open, normally closed
|
High level overflow is 1
|
Normally open, normally closed
|
Low is 1, high is 1
|
Normally open, normally closed
|
Alarm status, load output: normally open disconnect, normally closed
(The relay is disconnected, the load is disconnected and enters protection)
|
Low is 1, high is 0
|
Normally open, normally closed
|
When the inlet water detection is 0,
|
Normally open and open, normally closed (returned off state, load disconnected into protection)
|
Fourth, the basic function introduction:
1. Automatic water level control: The water level is lower than the low level induction probe, the water pump is automatically started, the water level rises to a high level, and the water pump is automatically turned off.
2. Idle idle delay pump: If there is no water in the water supply pipe after startup, the pump will be turned off after 3~5 minutes. During the pumping process, if the water flow is interrupted for more than 3 seconds, the pump is immediately turned off.
3. Automatically track the water source: start the pump every two hours after the pump is stopped, until the water is full.
4. Manual automatic switching: The controller will enter the automatic working mode by default. Press the K1 key to switch the working mode. The red light is in the automatic mode and the red light is in the manual mode.
5. Non-contact induction probe: It adopts non-contact capacitive sensing technology and special induction control chip design. The probe has durability, strong anti-interference ability, sensitive sensitivity, no contact with liquid, corrosion resistance, safety, environmental protection and pollution-free.
