Type:Logic ICs
Condition:New
Model:DJL-C372-2P
Texture of material:polymer
Place of Output Model Category:Switch Sensor
Working principle:Humidity Sensor
Sensor Category:Liquid level sensor
working voltage:220V

The following conditions must be met
1: Metal vessel wall thickness requirement 2-8MM
2: No paint is required on the container.
3: Require less liquid impurities
4: The diameter of the container should not exceed two meters.
5: Temperature up to 60 degrees
6: Require only liquid in the container.

DJL-C372-2PHigh and low liquid level two detection head high and low controller.

Product Description:

DJL-C372-2PHigh and Low Position ControllerandDS1603DA V1.0Two liquid level detection heads realize liquid level control function: when the containerTriggering low-level alarm signal from low-level sensor when the liquid level is too lowC372The controller closes the relay to start the pump to add liquid level. When the liquid level reaches a certain height, the high liquid level sensor sends out a signal to trigger.C372The controller disconnects the relay and automatically stops the pump working, so that it can circulate. Thus it can be realized.The Function of Automatic Control of High and Low Level of Metal ContainerKeep the liquid level of the container stable.

Product characteristics

1. AC95~265VWide Voltage Supply

2. Output of relay trunk node, suitable for multiple load control

3. Diversified control, manual or automatic mode control of pumps

4. Installation is simple and convenient. It can be positioned by screw or mounted by electric box track.

Electrical parameters

Model	C372-2P	Name	C352High and Low Level Automatic Controller
input voltage	AC100V-220V,50/60 Hz
working voltage	DC12V
Working Current	Working current <110 MAThe static current consumption is less than or equal to20mA
Load power	1.6KWBelow (AC contactors are required for overloading or three-phase pumps)
Alarm output	800W(Resistive Load) Normally Open and Normally Closed Output
Output mode	Relays often turn on or off or coMmunicateAC110V/220Vtwo types2Choose an output
Input signal	Low-level induction signal input; High-level induction signal input;
Inductor interface voltage	DC 12V
working temperature	-10~75Temperature
Shape size	115*90*40

Corresponding Diagram of Signal Input and Relay Output

Input signal	Load Output		Alarm signal status	Alarm output
The lowest position is0The top position is0	Normally open and closed, normally closed and disconnected	Follow ring	The lowest position is0The top position is1	Normally open and closed, normally closed and disconnected
The lowest position is1The top position is0 (raising of water level)	Normally open and closed, normally closed and disconnected		High spillover1	Normally open and closed, normally closed and disconnected
The lowest position is1The top position is1	Often open and open, often closed		Alarm status, load output: often open and open, often closed (Relay disconnected, load disconnected into protection)
The lowest position is1The top position is0 (Water level drop)	Often open and open, often closed

4. Introduction of basic functions:

1.Automatic water level control:When the water level is lower than the low-level induction probe, the pump is automatically started, the water level rises to the high level, and the pump is automatically closed.

2.Manual automatic switching:Controller starts by default and enters automatic mode. PressK1Key can switch working mode, red light is automatic mode, red light is manual mode.

3.Non-contact induction probe: Using non-contact ultrasonic induction technology and special induction control chip design, the probe has durability, strong anti-interference ability, sensitive induction, no contact with liquid, anti-corrosion, safety, environmental protection and pollution-free.

Parametric term	DS1603	Company	Remarks
working voltage	3.3-12	V	DC
average current	<35	mA	(1)
Blind zone distance	Less than 50	Mm	(2)
Detection Vessel Width	50-3000	Mm	(2)
Work cycle	1	S
Output mode	Switching Volume
Driving current	1	A
With liquid response time	1	S
Non-liquid response time	1	S
Normal temperature accuracy	(+3+H*0.5%)	mm	(3)
ESD	+4/+8	KV	(4)